How To Set Up A 10x10 Tent

Download Article

Download Commodity

Staking your favorite canopy tent into the grass is an easy task. But if you need to assemble your tent on concrete, you'll have to figure out how to weigh it down so the canopy doesn't blow away. Fortunately, you have multiple options for making inexpensive, homemade weights for your tent. These include weights fabricated with buckets of water or sand, store-bought tent weight bags, cinder blocks, or PVC pipage.

one
Buy tent weight bags for an easy pick. There are tent weight bags manufactured and marketed specifically for canopy tents. Usually you have to fill up them with sand and and then attach them to the frame and legs of your tent. These can exist more expensive than the bootleg options, simply they volition save you fourth dimension.^[i]
- Be sure that the weight of the full tent weight numberless run across your event's weight requirement, if you are using your tent at a public result. Check the tent weight packaging to encounter how much the weights weigh when they're full, and be certain to follow all directions.
2
Try cinder blocks as tent weights. A typical cinder block weighs about 28 pounds (13 kg), and can be useful as a tent weight. Necktie a rope around the cinder block and knot the rope at the tiptop corner of your tent frame. You lot can also necktie the cinder block to the tent leg using rope or bungee cord, while still attaching rope to the top frame.^[2]
- Some public events do not allow cinder blocks to be used every bit tent weights, as they can be a tripping hazard, so check with your outcome coordinator before using them.
- Cinder blocks can exist a user-friendly method of weighing down your tents at home. Consider covering them with old towels or sheets so people don't scrape themselves if they crash-land into them.
Advertizing
three
Use exercise weights to cut costs. If yous take exercise weights lying effectually at home, you tin also utilize these as weights for your tent. Stack a few of your option by your tent leg, lining up the holes. Thread rope through the holes, tie a knot around the weights, and then another knot at the top of your tent frame to adhere the weights to it.^[three]
- If yous are using your tent at a public event, bank check with your result coordinator before using exercise weights as tent weights.
Advertisement

i

Accept 4-8 5 Us gal (nineteen L) buckets to where you're setting up your tent. The benefit of using saucepan weights is that you can keep them empty until you demand them. This is particularly convenient if you know there will be water, sand, or gravel at your effect location. Utilize buckets with handles for the convenience of having somewhere to easily tie rope for attaching the weights to your tent.^[4]
2
Fill your buckets with the amount of filler needed. Public events with tents, such as arts festivals, oft accept a weight requirement for each tent leg. The highest requirement is unremarkably around forty pounds (18 kg) per leg. You'll need a dissimilar amount of filler depending on which filler yous'd like to employ.
- To apply water as your filler, make full your buckets all the way full to go 40 pounds (18 kg) in each i.
- For sand, yous'll need 3.2 gallons (12 L). Fill your buckets most two/three full of sand to become this.
- A total five US gal (xix L) bucket of gravel easily weighs 75 pounds (34 kg), so you'll only need a little over half a bucket full of gravel to use that pick.
three

Make full buckets with concrete for permanent weights. Some people prefer to make bucket weights with physical. Mix dry cement with h2o co-ordinate to the cement handbag's bundle directions, and fill the buckets half full with concrete. These of course will not be able to be emptied when you're finished with them, just they tin serve as permanently available weights for whenever you need them.
4

Attach a bungee cord or rope to the handle of each bucket. Clip a bungee string, or tie a sturdy knot with rope, to each of your bucket handles. If you're using rope, information technology will demand to be long enough to reach the top frame of your canopy with a knot tied there. A bungee cord will demand to be able to stretch that far besides.
5
Connect the other terminate of cord or rope to your tent frame. Connect your rope or cord to the corner of your tent frame near the leg so that the bucket hangs close to, or on, the ground. If the bucket is hanging at all, use another slice of rope or bungee cord to attach it to the tent leg. This will prevent it from swinging and spilling, or condign a tripping gamble to people walking by.
- Try putting a lid on the saucepan if y'all have i for it.
- If you used h2o equally your filler, keep the bucket on the ground while attaching it, or make full information technology at the spot of your tent, to avoid spilling besides much of the h2o.
Advertising

1
Purchase PVC pipe and other supplies at a hardware shop. For this option yous'll need 8 4 inches (10 cm) diameter PVC caps, a power drill, center protection, gloves, xvi each of nuts, bolts and washers in ⁵⁄₈ inch (1.vi cm) size, and 4 eyebolts that are ⁵⁄_eight inch (i.6 cm) in size. You lot'll too need 4 pieces of 36 inches (91 cm) PVC pipe, some PVC primer and glue, at to the lowest degree fifty pounds (23 kg) of fast-drying cement, water, a container for mixing cement, and rope or bungee cord.
- When finished, these weights will weigh about 40 pounds (18 kg) each. Y'all besides have the option of making smaller weights, using shorter 2 feet (61 cm) pieces of 3 inches (7.6 cm) diameter piping.
- Some people like to make 8 smaller weights of about 20 pounds (9.1 kg) each to make them easier to transport.
2
Drill holes into 4 of your PVC piping caps. Make a mark using permanent mark in the center of your pipe caps. Using a ⁵⁄₈ inch (1.6 cm) drill bit in your ability drill, drill a hole into the heart of 4 of the caps.^[5]
- Ever use center protection and gloves when operating power tools.
iii

Attach ^v⁄₈ inch (1.half-dozen cm) eyebolts to the caps with nuts and bolts. Insert 1 eyebolt into each hole that you drilled. Twist a ⁵⁄₈ inch (1.six cm) nut onto the eyebolt on either side of the cap to sandwich your eyebolt in, identify a washer on the inside stop, and and so twist a bolt on that end to secure it.^[6]
4
Glue the caps with eyebolts onto the PVC pipes. Most PVC glues have a brush inside the cannister, and require yous to use a purple primer liquid, sold nearly the glue itself, before brushing on the glue.^[7]
- Follow all instructions on the PVC glue as you brush the mucilage on and attach caps to what will be the tops of each of your pipes. Allow your gum to dry for the length of time determined by the gum instructions.
5
Mix some concrete and make full each piping. Use a 5 United states of america gal (19 50) bucket to mix your dry out cement with h2o co-ordinate to your cement package directions. Keep in mind that the cement starts to set up chop-chop, and then y'all'll need to work quickly. When each pipage is full, stand up it against a wall on the eyebolt to let the concrete dry out.^[viii]
- This stride tin benefit from the help of a friend. When the concrete is mixed, 1 person can fill the pipes with a minor trowel while the other person holds the pipe upright and occasionally taps information technology on the basis to brand sure the concrete is moving toward the bottom.
- Consider mixing your cement in 2 split up batches, and then that you aren't every bit rushed to use up all the cement at once before it starts setting.
vi

Drill a pocket-size hole in each of the bottom caps. The caps for the bottoms of your pipes will need a small hole in them to let air to escape when gluing the caps on. Wearing centre protection and gloves, utilize a pocket-sized drill bit to drill a hole into these plain caps.^[9]
7
Allow the physical to dry out and glue a cap bottom on each end. Allow the concrete inside your pipes to dry out completely for a few hours. Take the unattached cap bottoms and your PVC glue and primer, and glue these caps to the bottoms of your pipes. Allow them to dry according to the glue instructions.^[10]
- Your weights are now complete. Hang onto them until you lot need them for your assembled tent.
viii
Connect each weight to your tent frame with bungee cord or rope. To adhere your weights to your assembled tent, clip a bungee cord or tie a rope around the eyebolts. Accept the other end and prune or tie it to the tent frame at the acme corner nearly the leg of your tent, giving plenty length to the cord or rope so that the weight hangs near or on the ground. Do this to all 4 corners of your tent.
- Some people also like to tie the weights to the legs downwards well-nigh the footing with rope or Velcro strips, so that they don't swing around or become a tripping take a chance.
Advertisement

Add New Question

Question

I don't understand step iii. What practise you exercise with the bolt?

Method 3, step 3 says to, "Attach 5⁄8 inch (1.6 cm) eyebolts to the caps with nuts and bolts." In each hole yous drilled (in the caps), put in an eyebolt using nuts and bolts. It'south OK to attach them any other fashion as long as they are secure.

Enquire a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Thanks for submitting a tip for review!

Things You'll Need

Shop bought tent weight bags
Cinder blocks
Do weights
Rope or bungee cord

iv-8 5 gallons (19 L) buckets
Filler of your choice
Rope or bungee cord

8 4 inches (10 cm) diameter PVC caps
Power drill, eye protection, gloves
⁵⁄₈ inch (1.6 cm) nuts, bolts, and washers (16 of each)
4 ^v⁄₈ inch (i.6 cm) eyebolts
iv pieces of 36 inches (91 cm) PVC piping
PVC primer and mucilage
Fast-drying cement – at least 50 pounds (23 kg)
Water
Container for mixing cement
Rope or bungee string

Almost This Commodity

Article Summary X

The easiest way to hold downwards a canopy tent on concrete is to purchase tent-weight numberless, which can exist filled with sand and attached to the legs of the tent. Consider using cinder blocks or exercise weights every bit a potentially cheaper alternative to weight bags. However, these can exist a tripping run a risk, so ask your event coordinator earlier using these to concord down your tent. When using household items, make sure they add up to your issue'south weight requirement, or else your tent might not hold up. To brand a bucket weight, purchase 4 to 8 buckets that agree 5 gallons and fill up each ⅔ of the way with sand. If yous desire to apply gravel, only fill the buckets halfway. For permanent bucket weights, mix dry cement with water and fill up the buckets halfway with concrete. Let the mixture dry and you'll have tent weight whenever you lot need them. To learn more, including how to brand tent weights out of PVC piping, read on.

Did this summary aid you?

Thank you to all authors for creating a page that has been read 97,975 times.

Did this article help you?